Online Electrician Apprentice Training and Career Center

Welcome to Electrician Apprentice Headquarters! The information you find here will help you learn how to become an electrician. The IBEW, IEC, and ABC apprenticeships are the major education providers to today's electrician.

Our goal is to help you answer questions about electrician pay, apprenticeships, tools, job site atmosphere, and more!
Home / Electrical / How To Measure Current with a Clamp Accessory
fluke clamp accessory

How To Measure Current with a Clamp Accessory

Learning to measure current with a clamp accessory is a super simple process as long as you follow some simple steps. Believe it or not, you can measure DC current with a clamp as long as the meter is capable of interpreting the data.

 

This article comes straight from Fluke’s website and is extremely informative.

Not many electricians know how to use a clamp accessory to measure DC current and you’re going to learn about it now.

How To Measure Current with a Clamp Accessory

measure current with a clamp accessory

  1. Determine if the current to be measured is ac or dc.
  2. Select a clamp accessory for your multimeter that is designed to measure that specific current or one that can measure both ac and dc.
    Note: Look at the accessory clamp’s specifications and determine whether the clamp outputs a current level or a voltage level.
  3. Determine the circuit’s anticipated maximum current by checking the nameplate of a component or the breaker rating. Plug-in clamp accessories are available in a variety of preset ranges. Determine if the range of your multimeter or clamp accessory is high enough to measure it. If not, select an instrument equipped for higher ranges.
    Note: If a meter includes fused current terminals, verify that its fuses are good.Set up your DMM as follows:
    • To measure ac current with a current output clamp, turn the dial to mÃ/Ã.
    • Plug the black test lead into the COM jack.
    • For plug-in clamp accessories that produce an ac current output, plug the red test lead into the mÃ/Ã jack. These clamps are designed to measure ac current only and, depending on the clamp’s scaling factor, deliver 1 mA to the DMM for every 1 A of measured current (1 mA/A).
    • Follow steps 6-8 below.
    • To measure ac/dc current with a voltage output clamp, turn the dial to mVac for ac current, or to mVdc for dc current.
    • Plug the black test lead into the COM jack.
    • For plug-in clamp accessories that produce a voltage output, plug the red test lead into the V jack. These clamps are designed to deliver 1 mV, 10 mV or 100 mV to the DMM for every 1 A of measured current.
    • Follow steps 6-8 below.
  4. Open the jaws by pressing the tool’s trigger.
  5. Enclose a single conductor inside the jaws. Make certain the jaws are completely closed before taking readings.
  6. View the reading in the display.Tip: Clamps measure current in a circuit by measuring the strength of the magnetic field around a single conductor. Whenever possible, separate the test conductor from surrounding conductors by a few inches.The goal: Prevent the clamp from picking up stray magnetic fields. If separation is not possible, take several readings at different locations along the same conductor. Do not measure shielded conductors, as the magnetic fields are greatly diminished or even eliminated.

Current Measurement Analysis

Knowing the current consumption in a system, component or circuit is very helpful during troubleshooting.

Electrical components such as motors often carry a nameplate that displays the component’s circuit rating. A current measurement can be compared to that rating to determine the health of the component’s operating condition.

Take current measurements: to determine how much a load (a component, such as a motor) is drawing from the system. You can also measure the total load on a circuit.

A motor, for example, is overloaded if it draws more than the rated current, underloaded if it draws less.

When troubleshooting, a technician can take a baseline measurement and be on the lookout for overload, overcurrent or a current imbalance between phases.

Generally, higher-than-rated currents usually indicate a problem which can cause additional problems. Higher current produces higher temperature, and that may cause insulation breakdown and component failure.

Most digital multimeters can only measure dc or ac current up to 10 A. Higher current must be scaled down with a current clamp accessory, which can measure current in a circuit from .01 A to 1000 A by measuring the strength of the electric field around a conductor.

For maximum efficiency, it is recommended that a current measurement be taken when equipment is first installed and during normal operation. These measurements can be used to provide a baseline comparison when troubleshooting a future problem.

Reference: Digital Multimeter Principles by Glen A. Mazur, American Technical Publishers.

Education Is Critical

In the quest to make all apprentices a better electrician I’m constantly digging around the internet to bring you valuable information. If you haven’t visited Fluke’s website there is a ton of great information available.

When you go to the site click on the Training tab and a sub menu drops down. These three items is where you want to focus your time.

  • Electrical Safety
  • Measurement Basics
  • Test Tools Basics

Each selection has a drop down menu for more items.

Fluke clamp accessory screenshot

Select the one you want to learn about and you’ll be taken to another page with all sorts of learning topics.

arc flash training

I hope you found this article useful. Make sure you share with others.

 

Comments

comments

GET MORE!
Join other visitors who are receiving our newsletter and learn more about the electrical trade and how to become a great electrician.
We hate spam. Your email address will not be sold or shared with anyone else.

About Alex M

Alex M
Hard Work Puts You Where Good Luck Can Find You

Check Also

highlighted nec code book

How To Prepare Your NEC Code Book For An Electrical Exam

Whether you’re a first year apprentice or getting ready to take the journeyman’s or master’s …